Search This Blog

Saturday, January 28, 2012

I need to re-wire this old sewing machine

On so many occasions, I have found myself having to re-wire an entire sewing machine just so I could work on it. The 50+ year old machines usually have at least 1 cord that needs replaced.   That old wire insulation breaks down after time. The even older machines had cloth insulation on the electric cords which is even more dangerous. The wire to the light is the least likely to need replaced but still check it out carefully. The foot controller and power cord usually need to be replaced for safty purposes. The good news is that these older machines can be re-wired fairly easily. Some are easier than others. The light fixtures are the most difficult. It will require some soldering in most cases.  This 1940, Singer model 66 had the splices for the power cord, the light and the foot controller inside the motor mount. Starting with the light on this machine, You have to remove the wire retaining rings to get the fixture open. The glass lens was missing on this fixture.
You just pry the rings off with a small screw driver. This model has a large one at one end and a small one at the other. Once inside, you need to cut the old wire off of the switch contact and the bulb socket.
This will make more sense as you see for your self the old wire and what you must do to install new wire in the fixture. Yes, it can be scary the first time you try this. Just remember, somebody, just like you, put this together back in the old days.  Pictured below is the new wire soldered to the appropriate pieces.
Installing this back into the original fixture can be time consuming. You have to get the wire path just right so the two halves fit back together snug. It may take several tries. I made up several new 4-letter words while attempting this. I will not share my words with anyone. You must make up your own. I did run into one other problem that was not a normal "re-wire" issue. The center bulb contact in the socket had broken off. I had to make a new one. I folded some copper foil I had and slid it down into the slot and then soldered it in. You should not have to do this but this really shows the "do what you gotta do" attitude you must have in dealing with some of these old sewing machines.
 Now for the splicing of the power wire, the foot controller and the light in the motor mount.
 All the new wire is in and just needs to be cleaned up, insulated and tucked in. I used 2-wire nuts and a shrink tube case to protect the splices. Shrink tubing can be wonderful by itself in protecting old wire.I used wire ties to keep the wires from pulling out of the case.
The foot controller is the easiest part to re-wire. Most are easy to open up and replacing the old wire is straight forward. I use wire ties here also to lock the wire inside the controller.
If you made it through this much of this post, you may wonder where I get the new wire for the project. I found that buying cheap extension cords at the thrift store is the least expensive. Try to find some that are flexible and not so stiff. Cut the length that you need and leave the plug on for the power end. There should be enough information here for most people to rewire most of the old machines. This Model 66 was different than most since it spliced in the motor mount instead of the standard, Singer, 3-prong jack/plug. The prongs are numbered if you look close inside and are even color coded. Please be careful. I have blown the circuit breaker on more than one occassion. Click on the diagram below for a larger image. The area inside the shaded "Standard Singer Jack" is exactly the same wiring as the above model 66 motor mount splice. There are some other configurations that include a power recepticle where you plug the light into 1 socket, and the motor into the other. They still wire the same.

12 comments:

  1. Thank you for sharing these instructions. Now the Mister has a reference when he finally gets around to rewiring my latest 'rescues'.

    ReplyDelete
  2. Hi there. Nice blog. You have shared useful information. Keep up the good work! This blog is really interesting and gives good details. Water Soluble Flux , soldering fluxes .

    ReplyDelete
  3. Thank you for an easy to follow lesson on rewiring an old Singer light fixture!

    ReplyDelete
  4. The trend of the readings over a period of time will help identify the presence of anomalies. cm 1500 insulation machine

    ReplyDelete
  5. I... I have no idea what to do. I acquired a Singer 66-18...I don't even know how or where to plug the foot pedal into the machine. I'm just clueless there...

    I think it needs to be completely rewired because the outside is stiff and cracking and stripping and I can see the wires. I don't even know it using the cord off a lamp will even work...

    ReplyDelete
    Replies
    1. I found this current site in hopes of re-wiring my Singer 66-16 machine. Following is the link for your machine on a site I found my owners manual on. Good Luck. http://ismacs.net/singer_sewing_machine_company/manuals/singer-model-66-18-sewing-machine-manual.pdf

      Delete
  6. This comment has been removed by the author.

    ReplyDelete
  7. Just curious if you can give more details about rewiring a power receptacle. One where the light and motor plug into. I have a a vintage machine that I bought that needs that part and the foot pedal rewired. Do you have to purchase new insides for the receptacle and if so where would I get them?

    ReplyDelete
    Replies
    1. I have a similar machine to yours and I am going to get a small junction box to wire the motor and light directly. I can't find a replacement inline receptical and the insides of mine are too integrated with the box.

      Delete
  8. I'm in process of rewiring a 1947 singer 66-16, got the wiring done as shown in the diagram, but the motor runs continuously even without the foot pedal being pressed. What did I do wrong?

    ReplyDelete
  9. When purchasing the new electrical wire, is there anything specific we need to look for

    ReplyDelete